Neopixels (ws2812) help me

[mohammadali]

درود دوست عزیز نصب راحتی داره شما میتوانید از کتابخانه زیر کمک بگیرید
Adafruit NeoPixel و کتابخونهٔ fastLED


دوپین (+5 =VDD) و پین (VSS = Ground ) که معلومه چطور وصل میشند میمونه اخرین پین ( Di ) که شما از ماژول led که با ی مقاومت 470 اهم به پین دیجیتال 6 اردینو وصل میکنید طبق تصویر

در ضمن ( Do ) برای بشتر کردن طول این ریسه میباشد

و در اخر اینم دو کد زیبا برای شما دوست عزیز

#include <Adafruit_NeoPixel.h>

#define PIN 6

// Parameter 1 = number of pixels in strip
// Parameter 2 = pin number (most are valid)
// Parameter 3 = pixel type flags, add together as needed:
//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
Adafruit_NeoPixel strip = Adafruit_NeoPixel(60, PIN, NEO_GRB + NEO_KHZ800);

void setup() {
  strip.begin();
  strip.show(); // Initialize all pixels to 'off'
}

void loop() {
  // Some example procedures showing how to display to the pixels:
  colorWipe(strip.Color(255, 0, 0), 50); // Red
  colorWipe(strip.Color(0, 255, 0), 50); // Green
  colorWipe(strip.Color(0, 0, 255), 50); // Blue

  // Send a theater pixel chase in...
  theaterChase(strip.Color(127, 127, 127), 50); // White
  theaterChase(strip.Color(127,   0,   0), 50); // Red
  theaterChase(strip.Color(  0,   0, 127), 50); // Blue

  rainbow(20);
  rainbowCycle(20);
  theaterChaseRainbow(50);
}

// Fill the dots one after the other with a color
void colorWipe(uint32_t c, uint8_t wait) {
  for(uint16_t i=0; i<strip.numPixels(); i++) {
      strip.setPixelColor(i, c);
      strip.show();
      delay(wait);
  }
}

void rainbow(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256; j++) {
    for(i=0; i<strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel((i+j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

// Slightly different, this makes the rainbow equally distributed throughout
void rainbowCycle(uint8_t wait) {
  uint16_t i, j;

  for(j=0; j<256*5; j++) { // 5 cycles of all colors on wheel
    for(i=0; i< strip.numPixels(); i++) {
      strip.setPixelColor(i, Wheel(((i * 256 / strip.numPixels()) + j) & 255));
    }
    strip.show();
    delay(wait);
  }
}

//Theatre-style crawling lights.
void theaterChase(uint32_t c, uint8_t wait) {
  for (int j=0; j<10; j++) {  //do 10 cycles of chasing
    for (int q=0; q < 3; q++) {
      for (int i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, c);    //turn every third pixel on
      }
      strip.show();

      delay(wait);

      for (int i=0; i < strip.numPixels(); i=i+3) {
        strip.setPixelColor(i+q, 0);        //turn every third pixel off
      }
    }
  }
}

//Theatre-style crawling lights with rainbow effect
void theaterChaseRainbow(uint8_t wait) {
  for (int j=0; j < 256; j++) {     // cycle all 256 colors in the wheel
    for (int q=0; q < 3; q++) {
        for (int i=0; i < strip.numPixels(); i=i+3) {
          strip.setPixelColor(i+q, Wheel( (i+j) % 255));    //turn every third pixel on
        }
        strip.show();

        delay(wait);

        for (int i=0; i < strip.numPixels(); i=i+3) {
          strip.setPixelColor(i+q, 0);        //turn every third pixel off
        }
    }
  }
}

// Input a value 0 to 255 to get a color value.
// The colours are a transition r - g - b - back to r.
uint32_t Wheel(byte WheelPos) {
  if(WheelPos < 85) {
   return strip.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
  } else if(WheelPos < 170) {
   WheelPos -= 85;
   return strip.Color(255 - WheelPos * 3, 0, WheelPos * 3);
  } else {
   WheelPos -= 170;
   return strip.Color(0, WheelPos * 3, 255 - WheelPos * 3);
  }
}

[/QUOTE]
و این کد با تغییر

#include "FastLED.h"
// Number of RGB LEDs in the strand
#define NUM_LEDS 60 

// Define the array of leds
CRGB leds[NUM_LEDS];
// Arduino pin used for Data
#define PIN 6 

void setup()
{
  FastLED.addLeds<NEOPIXEL, PIN, RGB>(leds, NUM_LEDS);
}

void loop() { 
  // one at a time
  for(int j = 0; j < 3; j++) { 
    for(int i = 0 ; i < NUM_LEDS; i++ ) {
      memset(leds, 0, NUM_LEDS * 3);
      switch(j) { 
        case 0: leds[i].r = 255; break;
        case 1: leds[i].g = 255; break;
        case 2: leds[i].b = 255; break;
      }
      FastLED.show();
      delay(10);
    }
  }

  // growing/receeding bars
  for(int j = 0; j < 3; j++) { 
    memset(leds, 0, NUM_LEDS * 3);
    for(int i = 0 ; i < NUM_LEDS; i++ ) {
      switch(j) { 
        case 0: leds[i].r = 255; break;
        case 1: leds[i].g = 255; break;
        case 2: leds[i].b = 255; break;
      }
      FastLED.show();
      delay(10);
    }
    for(int i = NUM_LEDS-1 ; i >= 0; i-- ) {
      switch(j) { 
        case 0: leds[i].r = 0; break;
        case 1: leds[i].g = 0; break;
        case 2: leds[i].b = 0; break;
      }
      FastSPI_LED.show();
      delay(1);
    }
  }

  // Fade in/fade out
  for(int j = 0; j < 3; j++ ) { 
    memset(leds, 0, NUM_LEDS * 3);
    for(int k = 0; k < 256; k++) { 
      for(int i = 0; i < NUM_LEDS; i++ ) {
        switch(j) { 
          case 0: leds[i].r = k; break;
          case 1: leds[i].g = k; break;
          case 2: leds[i].b = k; break;
        }
      }
      FastLED.show();
      delay(3);
    }
    for(int k = 255; k >= 0; k--) { 
      for(int i = 0; i < NUM_LEDS; i++ ) {
        switch(j) { 
          case 0: leds[i].r = k; break;
          case 1: leds[i].g = k; break;
          case 2: leds[i].b = k; break;
        }
      }
      FastLED.show();
      delay(3);
    }
  }
}

[/QUOTE]