آپلود نشدن برنامه

[behroz2010]

سلام من میخواستم یک برنامه روی ایسیم بریزم اما ارو زیر میده




Arduino: 1.6.0 (Windows 7), Board: "Arduino Pro or Pro Mini, ATmega328 (5V, 16 MHz)"

Sketch uses 9,466 bytes (30%) of program storage space. Maximum is 30,720 bytes.

Global variables use 309 bytes (15%) of dynamic memory, leaving 1,739 bytes for local variables. Maximum is 2,048 bytes.

avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x01
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x01
Problem uploading to board. See http://www.arduino.cc/en/Guide/Troubleshooting#upload for suggestions.

This report would have more information with
"Show verbose output during compilation"
enabled in File > Preferences.

[magmagmary]

با آردوینو پرو مینی کار می کنی؟
اگه آره
یه بار در انتخاب بردت به جای پرومینی ، برد نانو رو انتخاب کن آپلود کن

[magmagmary]

البته اگه از پرو مینی استفاده می کنی اتصالاتت رو هم چک کن چون با مبدل داری کد میریزی

[behroz2010]

اره بازم خطا میده...

[magmagmary]

مبدلت رو چجوری به آردوینو وصل کردی؟

[magmagmary]

کدوم پین به کدوم پین؟

[behroz2010]

VCC ب vcc برد
gnd ب gndبرد
dtr ب dtrبرد
rxd ب rxبرد
txd ب txبرد

[magmagmary]

vcc - vcc
gnd - gnd
rx - tx
tx - rx
dtr - reset

[magmagmary]

پین ها باید مطابق چیزی که نوشتم باشن

[behroz2010]

درستش کردم تاثیری نداشت