نقل قول نوشته اصلی توسط Smead نمایش پست ها
من نمیدونم مشکلش چیه واسه خود منم این مشکل پیش اومد دقیقا همینطوری ولی برد اردوینو Uno داشتم
ای سیشو عوض کردم و یک ای سی که بوتلودر زدم بهش قرار دادم تو برد باز هم مشکل حل نشد و همون ارور میده!
واسه همین میگم احتمالا یا از پروگرامرش هست یا یک قطعه ای سوخته
سلام دوستان .مراحل بوت رو اشتباه انجام میدادم ولی با درست انجام دادن مراحل بوت این پیغام خطا رو دریافت کردم .ضمنا سیم بندی رو بر اساس لینک زیر انجام دادم و هیچ اشکالی نداره همچنین فیش مادگی مینی یو اس پی روی برد رو هم برا اطمینان عوض کردم تغییری حاصل نشد:
:
https://www.arduino.cc/en/uploads/Tu..._ISP_wires.jpg
but i have this error:
Arduino: 1.8.5 (Windows 7), Board: "Arduino Nano, ATmega328P (Old Bootloader)"

C:\Users\Arad\AppData\Local\Arduino15\packages\ard uino\tools\avrdude\6.3.0-arduino9/bin/avrdude -CC:\Users\Arad\AppData\Local\Arduino15\packages\ar duino\tools\avrdude\6.3.0-arduino9/etc/avrdude.conf -v -patmega328p -cstk500v1 -PCOM20 -b19200 -e -Ulock:w:0x3F:m -Uefuse:w:0xFD:m -Uhfuse:w:0xDA:m -Ulfuse:w:0xFF:m

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:00:53
Copyright (c) 2000-2005 Brian Dean, BDMICRO MAVRIC ATmega128 AVR Microcontroller Boards, Relays, and Optoisolators
Copyright (c) 2007-2014 Joerg Wunsch

System wide configuration file is "C:\Users\Arad\AppData\Local\Arduino15\package s\ar duino\tools\avrdude\6.3.0-arduino9/etc/avrdude.conf"

Using Port : COM20
Using Programmer : stk500v1
Overriding Baud Rate : 19200
AVR Part : ATmega328P
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PC2
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Block Poll Page Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff
flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff
lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00
calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00

Programmer Type : STK500
Description : Atmel STK500 Version 1.x firmware
Hardware Version: 2
Firmware Version: 1.18
Topcard : Unknown
Vtarget : 0.0 V
Varef : 0.0 V
Oscillator : Off
SCK period : 0.1 us

avrdude: AVR device initialized and ready to accept instructions

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000 (retrying)

Error while burning bootloader.
Reading | ################################################## | 100% 0.02s

avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.


avrdude done. Thank you